ZCUT-870 Reduce waste and good for your environment. Movable Sensor can set the place where Turn Table stops. Set cut pieces by Movable Sensor. Increase productivity. Provide consistent tape lengths. Accept to cut many kinds of tape. Clean and neat cut. Bobbin free, can put any size of roll. Change the length of tape and spacing by knob. Easy to change the blades without adjustments. ZCUT-9 Any size of tapes fit without bobbins. Cut length from 5mm to 999mm. Safety function and design. Memory function enable set six different length before use. Enable to cut Protection Film, Copper Foil, Aluminum Foil, Insulation material and more. Enable to hold the film or tape by using Flexible Tape Support. Preset and Loop counter functions. Compact body answers to Cell-System. Enable to use 2 rolls at the same time. Dual Photo Sensor. Build-in Tweezers, Oil, and Separator. ZCUT-9RP ZCUT-9RP has a special function to peel off the back paper of tape. The maximum outside diameter of roll is 150mm. we can only supply in set unit. Aluminum Foil Copper Foil tape are usable. Please send a whole tape sample to us before using this model. ZCUT-9 Program 12 different lengths can be programed to cut. Enable to cut in order which has been programed. Some of usable tapes may not cut depends on material/tape manufacturer. The length of tape might be have an error depends on types of tape. Specification are subject to change without prior notice. ZCUT-6 One machine can cover wide range of tape. (15-80mm width) Auto feed & cut. Easy to change blade and inexpensive blade cost. Simply set length by digital counter. Tough body enables to stand 24 hours being used. Compact body. ZCUT-6KP Custom-Made Dispenser for the Exclusive Use of Kapton Tape. Auto feed and cut. No curl after cutting. (straight cut.) Easy to change blade and inexpensive blade cost. Adjust the length by a digital counter. Using a popular blade that able to get anytime anywhere you want Exchange of blades is also very easy. ZCUT-6 W/STAND One machine can cover wide range of tape. (15-80mm width) Auto feed and cut. Easy to change blade and inexpensive blade cost. Adjust the length by a digital counter. Tough body enables to stand 24 hours being used. Compact body. ZCUT-3 Simply adjust the length by a digital counter. Automatic mode enables to cut a tape continuously at steady tempo.     (To change the pace of the process, turn the control knob) Manual mode takes out a new piece of tape after the cut tape are taken out. Greater efficiency on your work. Enable to cut non adhesive materials. (Protection Tape, Aluminum Foil Tape, etc.) Designed to work for a long period of time. ZCUT-3080 Simply set length by digital counter. Automatic mode enables to cut a tape continuously at steady tempo.     (To change the pace of the process, turn the control knob) Manual mode takes out a new piece of tape after the cut tape are taken out. Greater efficiency on your work. Enable to cut non adhesive materials. (Protection Tape, Aluminum Foil Tape, etc.) Designed to work for a long period of time. ZCUT-3150 Simply set length by digital counter. Automatic mode enables to cut a tape continuously at steady tempo.     (To change the pace of the process, turn the control knob) Manual mode takes out a new piece of tape after the cut tape are taken out. Greater efficiency on your work. Enable to cut non adhesive materials. (Protection Tape, Aluminum Foil Tape, etc.) Designed to work for a long period of time. ZCUT-3250 Simply set length by digital counter. Automatic mode enables to cut a tape continuously at steady tempo.     (To change the pace of the process, turn the control knob) Manual mode takes out a new piece of tape after the cut tape are taken out. Greater efficiency on your work. Enable to cut non adhesive materials. (Protection Tape, Aluminum Foil Tape, etc.) Designed to work for a long period of time. ZCUT-3RP Peel off and cut the back paper. Aluminum Foil and Copper Tapes are usable. The maximum outside diameter of roll is 150mm. we can only supply in set unit. ZCUT-3AS Countermeasure against electrostatic problem this model is suitable to apply on sensitive,     precision work piece. To avoid electrostatic problem, we always need to pay attention to every environment. ZCUT-AS is designed as for withstand multiple purposes. The body is made of stainless steel without any plastic parts.     The voltage reading for static type is less than 5 volts. It gets more effective by using anti-static tape. ZCUT-3NW Enable to cut tape width 5 mm. Easy to change the blades without adjustments. ZCUT-3SB Fold one edge of adhesive tape continuously, so you can easily to peel off     the tape by pulling the non-adhesive side. For the operations that need to peel off the sticked tape,     ZCUT-3SB improves its efficiency and be able to appeal to the end users. ZCUT-3 W/STAND Simply set length by digital counter. Automatic mode enables to cut a tape continuously at steady tempo.     (To change the pace of the process, turn the control knob) Manual mode takes out a new piece of tape after the cut tape are taken out. Greater efficiency on your work. Enable to cut non adhesive materials. (Protection Tape, Aluminum Foil Tape, etc.) Designed to work for a long period of time.